1. Ford Fusion
  2. Problems
  3. 2007
  4. Service Brakes, Hydraulic

2007 Ford Fusion Service Brakes, Hydraulic Problems

7
Owner complaint records in our dataset

Records are owner complaints, not a measured failure rate.

Owner complaint recordsComplaint records reflect reports in our dataset and do not measure how frequently the problem occurs across all vehicles.

Among these 7 stored complaint records:

  • 2 indicate a crash
  • 1 indicate injury
  • 0 indicate fire

Mileage in stored records

BandRecords
1–30k mi3
30–60k mi2
60–100k mi1
100–150k mi1

Complaint records

Owner-submitted complaint content, presented as stored.

  • October 8, 2012 · 125,000 miles

    Service Brakes, Hydraulic

    Tl* the contact owns a 2007 ford fusion. While driving approximately 45 mph, the brakes failed to stop the vehicle and excessive force was required. The failure recurred on numerous occasions. The vehicle was taken to a dealer, where it was diagnosed that the hydraulic control unit needed to be replaced. The vehicle was repaired. The manufacturer was notified of the failure. The approximate failure mileage was…

    ODI 10672699

  • November 20, 2011 · 60,000 miles

    Engine · Service Brakes, Hydraulic

    I had purchased my 2007 ford fusion new and had a few oddities during the course of ownership. Within two years of ownership i had a battery short out. At three years i had to have a hefty brake service done because of a clicking noise when the brakes were applied. I noticed at four years that when i would remove the key from the ignition and open the door, the car would chime as if the key was still in it. The…

    ODI 10535912

  • September 30, 2010 · 41,096 miles

    Air Bags · Seat Belts · Service Brakes, Hydraulic

    Tl*the contact owns a 2007 ford fusion. The contact was driving approximately 65 mph, the vehicle suddenly swerved into another lane. The brakes locked when pressure was applied and the vehicle began to spin uncontrollably. When the brakes were engaged there was a clicking noise coming from the rear of the vehicle. The vehicle would not slow down and accelerated up an embankment and into a dirt mound. The seat belt…

    Crash reported · 1 injury

    ODI 10365476

  • September 10, 2010 · 20,222 miles

    Service Brakes, Hydraulic

    I have just spent $230 to have the rear brake disks replaced on my 2007 ford fusion. They were so pitted from corrosion that they made a terrible noise when the brakes were applied. They might even have been a safety hazard for all i know. The front ones were replaced a month after i bought the car new in 2007 for the same reason. The car has been driven a mere 20,000 miles. The mechanic tells me that the front…

    ODI 10358923

  • July 27, 2010 · 74,000 miles

    Service Brakes, Hydraulic

    The power booster in my 2007 ford fusion failed after only a few months of the brakes feeling "off" at rare, random times. It went out, rendering my brakes useless over 55 mph and caused me to rear end someone because the brakes would not stop the car. *tr

    Crash reported

    ODI 10348523

  • February 25, 2008 · 300 miles

    Service Brakes, Hydraulic

    I have a ford fusion 07 the problem that i have is that the brake rotors rust so badly when i don't drive for a week or two the brakes shudder badly what can be done to correct this problem? I have a old 95 buick that is under the same carport that can set for a month or longer and does not shudder after sitting longer than the ford i am retired and do not drive either vehicle very much. *tr

    ODI 10219573

  • August 17, 2007 · 295 miles

    Idler And Attachment · Service Brakes, Hydraulic · Structure · Suspension · Switch

    2007 ford fusion bought new does not function well it takes a while to crank. Windows began to mold, car shakes, vibrates , swerves of road when brakes applied, brakes do not function well car makes noises. Tires do not perform well tires have trouble slowing down. *jb

    ODI 10203506

Catalog parts for this system

Catalog year/make/model rows for 2007 Ford Fusion.

Catalog fitment does not by itself prove OEM-equivalent compatibility.